-64%

Woodworking Dowel Jig Set – starrypiglet

$49.99 $17.99

This is ESSENTIAL for Woodworking!

FEATURES:

??Quick jig peg that self-centers within boards to make fast . accurate positioning joints.
??Capable of edge-to-edge . T . and edge-to-corner joints.
??Made of impact resistant plastic.
??Can be used on cards up to 31mm thick.
??Adapts 6 . 8 and 10mm drills.

SPECIFICATIONS:

Material:Carbon Steel
Internal Diameter : 1/8″ .3/16″ .1/4″ .5/16″ .3/8″ .7/16″ .1/2″ (3 . 4 . 5 . 6 . 8 . 10 . 12mm)

HOW TO USE:

1. NECESSARY ACCESSORIES FOR DOWELLING

You will need to use the following with the jig: dowel pins . a sharp pencil . a square . a tape measure for spacing out the pitch of the pins . you will also need a drill or a cordless drill and dowel drills fitted with depth stop for proper setup. You will also need some glue and clamps to finish up your joint. A simple clamp will come in handy when securing the workpiece.


2. MARKING OFF THE HOLE CENTRES

Place both pieces on top of each other . match the front and mark out the centres for dowel pins on the bottom workpiece. We recommend placing the first dowel at least 27 mm from the front and back. The distance between the pins is arbitrary. Remember that long distance between the pins usually means your joint won’t be strong enough. We recommend creating a distance of 65-100 mm. This will ensure a firm joint.

3. COPYING THE MEASUREMENTS ONTO THE SECOND PIECE

Mark out the pin holes onto the second piece using a square to properly set up the jig. Workpiece drilled in the face grain should have marks on the face and similarly . the end grain should have marks on the end of the wood.


4. PIN SIZE – DECIDING ON THE DRILLED DEPTH

Measure the total pin length and decide on the depth of drilling into the end and face grain. For this part . we have used 35 mm long and 18 mm thick pins. We drilled a 15 mm deep hole into face and 22 mm deep into the end grain. Always leave a 2mm space for some glue . this means 15 mm to face + 20 mm into the end + 2 mm space for glue.


5. DEPTH SETTING

Place the jig onto the workpiece . insert the drill into the sleeve until the drill hits the piece. The drilled depth equals the distance of the stop to the jig. Set up the height by moving the ring along the drill and secure it with a locking pin. Make sure to properly tighten the depth stop to prevent its travel which would alter the drilled depth.


6. SETTING UP THE JIG FOR EDGE DRILLING

The proper hole placement onto the centre of the piece and accurate set up of the distance of the pins are the most important fundamentals when drilling into the edge.

dowel jig

Place the jig onto the edge the right way to drill out a chosen diameter (as shown in the picture). Set up a proper centre by using centring studs and by rotating the handle the right way. Follow the marked out distance between the dowels and always position your jig so the mark is in the middle.


7. DRILLING INTO THE EDGE

Insert the drill into the hardened bushings and drill out the pinhole.

dowel jig

Proceed and drill out the retaining pin holes all the same.

dowel jig

8. SETTING UP THE JIG FOR FACE DRILLING

Fit the jig with a side stop and set the distance of drilling from the edge of the piece.
For simple set up . insert one pin into the hole in the edge and place the jig opening of a similar diameter over it. Press the side stop to the piece and tighten the fastening screws.

dowel jig


9. DRILLING INTO THE FACE

dowel jig

Use the depth stop to set up the depth of 15 mm and drill out the holes. The side stop secures the right distance from the side. The centring of pins is guided by the marked out guideline. Apply this procedure for all other pins.

dowel jig

TIP: Place the drill into a sleeve and mark out a place for the centre according to it . this is a simpler way of adjusting corners.

Reviews

There are no reviews yet.

Be the first to review “Woodworking Dowel Jig Set – starrypiglet”

Your email address will not be published. Required fields are marked *

Scroll to Top